;M8MPMIN.A86 -- Overlay file for the CompuPro I3/I4 under MPM86 with
;		 MSUP.RSP installed			 09/18/84
;
; This overlay adapts the MDM8xx program to the CompuPro Interfacer 3 or
; Interfacer 4 cards using the 2651 USART chip, running under MPM86 with
; MSUP.RSP installed.
;
; You will want to look this file over carefully. There are a number of
; options that you can use to configure the program to suit your taste.
; This file places particular emphasis on using an external modem that
; is connected to a serial port.  This includes acoustic modems as well
; as "intelligent" modems such as the Hayes Smartmodem, Racal-Vadic, Bell
; Dataphone 212A, etc.
;
; This overlay is capable of setting the baud rate, disconnecting the
; modem, and sending breaks.
;
;
;
;=========================================================================
;			<<< N O T E >>> 
;
;	To use MDM8xx with THIS overlay and running under MPM86 or MPM8-16
;	You MUST have MSUP.RSP installed.
;
;	To Install MSUP run your MPM GENSYS program and answer all questions
;	as in CompuPros MPM8-16 suplementary Manual except for the Number
;	of system flags which should be set to 51 .
;
;==========================================================================
;
;
;
;
;	TO USE: First edit this file filling in answers for your own
;		equipment.  Then assemble with ASM86.CMD or equivalent
;		assembler.  Then use M8CNFG to overlay the results
;		of this program to the original MDM8xx.H86 file:
;
;		ASM86 M8MPMIN
;		REN M8OVL.H86=M8MPMIN.H86
;		M8CNFG
;		GENCMD MDM 8080 CODE[MFF0]
;
;
; =   =	  =   =	  =   =	  =   =	  =   =	  =   =	  =   =	  =   =	  =   =
;
; 09/18/84 - Original Version			- Alex Soya
;						  P.O. Box 121
;						  Melbourne Beach
;						  Florida 32951
;
;
; =   =	  =   =	  =   =	  =   =	  =   =	  =   =	  =   =	  =   =	  =   =
;
BELL	EQU	07H			;bell
CR	EQU	0DH			;carriage return
ESC	EQU	1BH			;escape
LF	EQU	0AH			;linefeed
;
YES	EQU	0FFH
NO	EQU	0
;
; MPM function Call equates:
;
F_OPQUE EQU	135	; Open Que
F_RDQUE EQU	138	; Conditional Read Que
F_WRQUE EQU	140	; Write to Que
GETSYS	EQU	154	; Get SYSDAT address
;
;
; Xios Call Function Numbers
;
XCONST EQU	0	; XIOS Console Status check
XCONIN EQU	1	; XIOS Console Input function
XCONOT EQU	2	; XIOS Console Output
;
;
;
; Change the following to match your equipment
;
;
; =   =	  =   =	  =   =	  =   =	  =   =	  =   =	  =   =	  =   =	  =
;
BASE	EQU	010H			;base port of CompuPro I3 or I4 cards
UPORT	EQU	BASE+7			;user (chip select) port
MDM	EQU	6			;chip that controls modem port
;
;
;
DPORT	EQU	BASE			;data port
SPORT	EQU	BASE+1			;status port
MPORT	EQU	BASE+2			;mode port
CPORT	EQU	BASE+3			;control port
;
TBMT	EQU	01H			;transmit buffer empty
DAV	EQU	02H			;data available
;
	ORG	100H
;
; Change the clock speed to suit your system
;
	RS	3			;(for  "JMP   START" instruction)
;
PMMIMODEM	DB	NO		;yes=PMMI S-100 Modem			103H
SMARTMODEM	DB	YES		;yes=HAYES Smartmodem, no=non-PMMI	104H
TOUCHPULSE	DB	'T'		;T=touch, P=pulse (Smartmodem-only)	105H
CLOCK		DB	60		;clock speed in MHz x10, 25.5 MHz max.	106H
					;20=2 MHh, 37=3.68 MHz, 40=4 MHz, etc.
MSPEED		DB	1		;0=110 1=300 2=450 3=600 4=710 5=1200	107H
					;6=2400 7=4800 8=9600 9=19200 default
BYTDLY		DB	5		;0=0 delay  1=10ms  5=50 ms - 9=90 ms	108H
					;default time to send character in ter-
					;minal mode file transfer for slow BBS.
CRDLY		DB	5		;0=0 delay 1=100 ms 5=500 ms - 9=900 ms 109H
					;default time for extra wait after CRLF
					;in terminal mode file transfer
NOOFCOL		DB	5		;number of DIR columns shown		10AH
SETUPTST	DB	YES		;yes=user-added Setup routine		10BH
SCRNTEST	DB	YES		;Cursor control routine			10CH
ACKNAK		DB	YES		;yes=resend a record after any non-ACK	10DH
					;no=resend a record after a valid-NAK
BAKUPBYTE	DB	NO		;yes=change any file same name to .BAK	10EH
CRCDFLT		DB	YES		;yes=default to CRC checking		10FH
TOGGLECRC	DB	YES		;yes=allow toggling of CRC to Checksum	110H
CONVBKSP	DB	NO		;yes=convert backspace to rub		111H
TOGGLEBK	DB	YES		;yes=allow toggling of bksp to rub	112H
ADDLF		DB	NO		;no=no LF after CR to send file in	113H
					;terminal mode (added by remote echo)
TOGGLELF	DB	YES		;yes=allow toggling of LF after CR	114H
TRANLOGON	DB	YES		;yes=allow transmission of logon	115H
					;write logon sequence at location LOGON
RESERVED	DB	YES		;Reserved for Future Expansion		116H
LOCONEXTCHR	DB	NO		;yes=local command if EXTCHR precedes	117H
					;no=external command if EXTCHR precedes
TOGGLELOC	DB	YES		;yes=allow toggling of LOCONEXTCHR	118H
LSTTST		DB	YES		;yes=printer available on printer port	119H
XOFFTST		DB	NO		;yes=checks for XOFF from remote while	11AH
					;sending a file in terminal mode
XONWAIT		DB	NO		;yes=wait for XON after CR while	11BH
					;sending a file in terminal mode
TOGXOFF		DB	YES		;yes=allow toggling of XOFF checking	11CH
IGNORCTL	DB	NO		;yes=CTL-chars above ^M not displayed	11DH
EXTRA1		DB	0		;for future expansion			11EH
EXITCHR		DB	'E'-40H		;^E = Exit to main menu			11FH
BRKCHR		DB	'@'-40H		;^@ = Send 300 ms. break tone		120H
NOCONNCT	DB	'N'-40H		;^N = Disconnect from the phone line	121H
LOGCHR		DB	'L'-40H		;^L = Send logon			122H
LSTCHR		DB	'P'-40H		;^P = Toggle printer			123H
UNSAVE		DB	'R'-40H		;^R = Close input text buffer		124H
TRANCHR		DB	'T'-40H		;^T = Transmit file to remote		125H
SAVECHR		DB	'Y'-40H		;^Y = Open input text buffer		126H
EXTCHR		DB	'^'-40H		;^^ = Send next character		127H
;
;
	RS	3			;				128H
;
IN@MODCTL1:
	RET				;in modem control port		12BH
	DB	0,0,0,0,0,0,0,0,0	; spares
;
OUT@MODDATP:
	JMP	OMDP			;out modem data port		135H
	DB	0,0,0,0,0,0,0		; spares
;
IN@MODDATP:
	JMP	IMDP			;in modem data port		13FH
	DB	0,0,0,0,0,0,0		; spares
;
ANI@MODRCVB:	RET			;bit to test for receive ready	149H
		RS	2		; Nothing to do here for MPM
;
CPI@MODRCVR:	JMP TSTMODRDY		;value of rcv. bit when ready	14CH
;
;
ANI@MODSNDB:	RET			;bit to test for send ready	14FH
		RS	2		; Nothing to do here for MPM
;
CPI@MODSNDR:	XOR AL,AL		; test for send ready		152H
		RET			; Always ready for MPM
;
	RS	6			;				156H
;
OUT@MODCTL1:	RET 
	RS	2			;out modem control port #2	15BH
;
OUT@MODCTL2:	RET 
	RS	2			;out modem control port #1	15EH
;
LOGONPTR DW	(Offset LOGON)		;for user message.		161H
	RS	6			;				163H

JMP@GOODBYE:JMP GOODBYE			;				169H
JMP@INITMOD:JMP INITMOD			;go to user written routine	16CH
	RET	
	NOP	
	NOP				;(by-passes PMMI routine)	16FH
	RET	
	NOP	
	NOP				;(by-passes PMMI routine)	172H
	RET	
	NOP	
	NOP				;(by-passes PMMI routine)	175H
JMP@SETUPR:    JMP  SETUPR		;				178H
JMP@SPCLMENU:  JMP  SPCLMENU		;				17BH
JMP@SYSVER:    JMPS SYSVER		;make sure this is SHORT Jump	17EH
JMP@BREAK:     JMP  SENDBRK		;				180H

;
; Do not change the following six lines.
;
JMP@ILPRT:
		RS	3		;				183H
JMP@INBUF:
		RS	3		;				186H
JMP@INLNCOMP:
		RS	3		;				189H
JMP@INMODEM:
		RS	3		;				18CH
JMP@NXTSCRN:
		RS	3		;				18FH
JMP@TIMER:
		RS	3		;				192H
JMP@CTYPE:
		RS	3		;				195H
JMP@KEYIN:
		RS	3		;				198H

;
;
; Routine to clear to end of screen.  If using CLREOS and CLRSCRN, set
; SCRNTEST to YES at 010AH (above).
;
CLREOS: CALL	JMP@ILPRT		;				195H
	DB	ESC,'Y',0,0,0		;				198H
	RET				;				19DH
;
CLRSCRN:CALL	JMP@ILPRT		;				19EH
	DB	ESC,'*',0,0,0		;				1A1H
	RET				;				1A6H
;
SYSVER: CALL	JMP@ILPRT		;				1A7H
	DB	'Version for CompuPro '
	DB	'Interfacer-3 or 4 under MPM86 with MSUP.RSP'
	DB	CR,LF,0
	RET
;.....
;
;
;-----------------------------------------------------------------------
;
; NOTE:	 You can change the SYSVER message to be longer or shorter.  The
;	 end of your last routine should terminate by 0400H (601 bytes
;	 available after start of SYSVER) if using the Hayes Smartmodem
;	 or by address 0C00H (2659 bytes) otherwise.
;
;-----------------------------------------------------------------------
;
; You can put in a message at this location which can be called up with
; CTL-L if TRANLOGON has been set TRUE.	 You can use several lines if
; desired.  End with a 0.
;
LOGON	DB	' Isnt it nice to run 2 modem programs'
	DB	' at the same time?',CR,LF,0
;
;.....
;
;
;
;
;....
;
;
; Add your own routine here to send a byte in AL to Modem Data Port
;
OMDP:			    ; Send a character to the Modem console [MPM]
	PUSH DX			; savem				[MPM]
	PUSH CX			;				[MPM]
	PUSH BX			;				[MPM]
	PUSH DS			;				[MPM]
	MOV CL,AL		; Character to CL for XIOS	[MPM]
	MOV DL,COMCHA		; Console no to DL for XIOS	[MPM]
	MOV AL,XCONOT		; Send the guy out to modem	[MPM]
	CALLF CS:DWORD PTR XIOS ; via xios call			[MPM]
	POP DS			;				[MPM]
	POP BX			;				[MPM]
	POP CX			; restore regs			[MPM]
	POP DX			;				[MPM]
	RET			;				[MPM]

;
;
;....
;
; Add your own routine here to read Modem Data Port into AL
;
IMDP:			; Get a character from Modem Console	[MPM]
	PUSH DX			; savem				[MPM]
	PUSH CX			;				[MPM]
	PUSH BX			;				[MPM]
	PUSH DS			;				[MPM]
	MOV CL,COMCHA		; Get character to AL via	[MPM]
	MOV AL,XCONIN		; XIOS function call CONIN	[MPM]
	CALLF CS:DWORD PTR XIOS ;				[MPM]
	POP DS			;				[MPM]
	POP BX			;				[MPM]
	POP CX			; restore regs			[MPM]
	POP DX			;				[MPM]
	RET			;				[MPM]
;
;
;......
;
;
TSTMODRDY:		; see if a char is ready for caller	[MPM]
	PUSH DX			;				[MPM]
	PUSH CX			; savem				[MPM]
	PUSH BX			;				[MPM]
	PUSH DS			;				[MPM]
	MOV AL,XCONST		; Check Console Status via XIOS [MPM]
	MOV CL,COMCHA		; Modem is a CONSOLE		[MPM]
	CALLF CS:DWORD PTR XIOS ;				[MPM]
	CMP AL,0FFH		;				[MPM]
	JE CONRDY		; IS CONSOLE READY ?		[MPM]
	MOV AL,0FFH		; nope...			[MPM]
	JMPS CPIEX		;    tell caller and exit here	[MPM]
CONRDY: MOV AL,0		; yeap...			[MPM]
CPIEX:	OR AL,AL		;    nope so tell caller	[MPM]
	POP DS			;				[MPM]
	POP BX			;				[MPM]
	POP CX			;				[MPM]
	POP DX			;				[MPM]
	RET			;				[MPM]
;.....
;
;
;
; Add your own routine here to send a break tone to reset some time-
; share computers, if desired.
;
SENDBRK:PUSHF			; disable Interupts
	CLI
	CALL	SELECT			;select chip
	MOV	AL,2FH			;send break for 300ms
	JMPS	GOODBYE1
;.....
;
;
; Add your own routine here to put DTR low and/or send a break tone.
;
GOODBYE:PUSHF			; disable Interupts
	CLI
	CALL	SELECT
	XOR	AL,AL			;turn off DTR
;
GOODBYE1:
	OUT	CPORT,AL
	MOV	CH,3			;turn off DTR for 300 ms.
	POPF				; restore interupts
	CALL	JMP@TIMER
	PUSHF
	CLI				; disable Interupts again
	CALL	SELECT
	MOV	AL,27H			;turn DTR back on
	OUT	CPORT,AL
	POPF				; Interupts ok again
	RET
;.....
;
;
; You can use this area for any special initialization or setup you may
; wish to include.  Each must stop with a RET.	You can check the other
; available overlays for ideas how to write your own routines if that
; may be of some help.
;
;The following is used to initialize the xios and MXqueues for execution
;of MDM86.
;
INITMOD:
	MOV CL,GETSYS		; Find SYSDAT			[MPM]
	INT 224			; In MPM			[MPM]
	MOV AX,ES:.28H		; Find XIOS OFFSET		[MPM]
	MOV CS:XIOS,AX		;				[MPM]
	MOV AX,ES:.28H+2	; Find XIOS SEGMENT		[MPM]
	MOV CS:XIOS+2,AX	;				[MPM]

	CMP  BYTE PTR COMCHA,0	; Do we have a COM channel?	[MPM]
	JE  OPQU		; Yep, Continue Initialization	[MPM]
	JMP CONINT		;				[MPM]

OPQU:	MOV CL,161		; Attach LIST device		[MPM]
	INT 224			;				[MPM]
	OR AX,AX		; did we get it ?		[MPM]
	JE FCOMS		;   Yes, Proceed with COMS	[MPM]
	CALL JMP@ILPRT		; No, say so			[MPM]
	DB cr,lf,'+++ Printer Busy, NOT ATTACHED +++',cr,lf,0 ; [MPM]

FCOMS:	MOV AL,1		; Find available COM channels	[MPM]
	XOR BX,BX		; Start with Com Channel 1	[MPM]
NXTQ:	PUSH AX
	PUSH BX
	ADD AL,30H		; Make Ascii COMCH		[MPM]
	MOV QPBNAM+7,AL		;				[MPM]
	MOV CL,F_OPQUE		; Open the que			[MPM]
	MOV DX, OFFSET MXQPB	;				[MPM]
	INT 224			;				[MPM]

	MOV CL,F_RDQUE		; Can we read from the que ?	[MPM]
	MOV DX, OFFSET MXQPB	; Lets give it a try..		[MPM]
	INT 224			;				[MPM]

	OR  AX,AX		; Was it a good read ?		[MPM]
	JE  GOTCOM		; we got a COM channel		[MPM]
	POP BX			;				[MPM]
	POP AX			; restore these suckers		[MPM]
COMNEX: INC AL			; and try next			[MPM]
	CMP AL,6		; done them all ?		[MPM]
	JGE FNDALL		;   YEP, All channels found	[MPM]
	JMP NXTQ		; NOPE, Play it again SAM	[MPM]

GOTCOM: POP BX			;				[MPM]
	POP AX			;				[MPM]
	MOV COMLST[BX],AL	; Put Channel in list		[MPM]
	INC BX			;				[MPM]
	JMPS COMNEX		; and try one more		[MPM]

FNDALL: CMP COMLST,0		; Ok, lets see what we got	[MPM]
	JE  NOCOMS		; Nothing, so tell the guy	[MPM]
	CMP COMLST+1,0		; More than one COM channel ?	[MPM]
	JE SING			; YEAP, Lets be generous	[MPM]
	JMP COMCHC		;				[MPM]
SING:	MOV AL,BYTE PTR COMLST	; NOPE, One is all we need	[MPM]
	MOV BYTE PTR COMCHA,AL	; Keep it for us		[MPM]
	ADD AL,30H		; make ASCII Channel number	[MPM]
	MOV TELONE,AL		; stuff into message		[MPM]
	CALL JMP@ILPRT		; Tell the guy what the deal is [MPM]
	DB cr,lf,'Only One COM channel available',cr,lf ;	[MPM]
	DB 'Communications Channel '			;	[MPM]
TELONE	DB '0'			;				[MPM]
	DB ' connected.',cr,lf,lf,0			;	[MPM]
	JMP  CONINT		; Now do rest of initialization [MPM]

NOCOMS: CALL JMP@ILPRT		; Ah well, better luck next time[MPM]
	db cr,lf,'+++ NO COMMUNICATIONS CHANNEL AVAILABLE +++' ;[MPM]
	db cr,lf,0		;				[MPM]
	MOV CL,0
	INT 224			; Have a nice one.....		[MPM]
COMCHC: CALL JMP@ILPRT		; Give him CHOICE of channels	[MPM]
	DB cr,lf,'Available Communication Channels : ',0 ;	[MPM]
	XOR BX,BX		;				[MPM]
COMDIP: MOV AL,COMLST[BX]	; Get a Channel #		[MPM]
	CMP AL,0		; Is there one there ? Phew..	[MPM]
	JE  GETCEL		; Nope, Get Console selection	[MPM]
	ADD AL,30H		; Make ASCII			[MPM]
	CALL JMP@CTYPE		; Send it out			[MPM]
	CMP COMLST+1[BX],0	; More to do			[MPM]
	JE PNXT			; YES put in a comma		[MPM]
	MOV AL,','		;				[MPM]
	CALL JMP@CTYPE		;				[MPM]
	MOV AL,' '		;				[MPM]
	CALL JMP@CTYPE		;				[MPM]
PNXT:	INC BX			; Next...			[MPM]
	JMPS COMDIP		;				[MPM]

GETCEL: CALL JMP@ILPRT		;				[MPM]
	DB CR,LF,'Enter Selection :',0	 ;			[MPM]
	CALL JMP@KEYIN		; Get Anser			[MPM]
	PUSH AX			;				[MPM]
	CALL JMP@CTYPE		; Echo it			[MPM]
	POP  AX			;				[MPM]
	SUB AL,30H		; deASCII			[MPM]
	XOR BX,BX		; Valid COMM Channel ?		[MPM]
CONFRM: CMP COMLST[BX],0	; Lets go through what we got	[MPM]
	JE INVLID		; Ah well he wasnt too clever	[MPM]
	CMP COMLST[BX],AL	; WELL ?			[MPM]
	JE COMOK		; YEAP, all is fine		[MPM]
	INC BX			; and look for another one	[MPM]
	JMPS CONFRM		;				[MPM]

INVLID: CALL JMP@ILPRT		; Give out			[MPM]
	DB cr,lf,'+++ INVALID SELECTION +++',cr,lf,0	;	[MPM]
	JMP COMCHC		; Here we go again ....		[MPM]

COMOK:	MOV COMCHA,AL		; Keep the Channel		[MPM]
	XOR BX,BX		; Now write back what we dont	[MPM]
WRTMX:	CMP COMLST[BX],0	; Need.	 End of list ?		[MPM]
	JE CONINT		; YEap..  ah thats nice...	[MPM]
	MOV AL, BYTE PTR COMCHA ;				[MPM]
	CMP COMLST[BX],AL	;				[MPM]
	JE MYCOM		; DONT WRITE BACK THE ONE I WANT[MPM]
	MOV CL,F_OPQUE		;				[MPM]
	MOV DX, OFFSET MXQPB	;				[MPM]
	MOV AL,COMLST[BX]	; Make que name			[MPM]
	ADD AL,30H		; In ASCII please		[MPM]
	MOV QPBNAM+7,AL		;				[MPM]
	PUSH BX			;				[MPM]
	INT 224			;				[MPM]
	MOV CL,F_WRQUE		;				[MPM]
	MOV DX, OFFSET MXQPB	;				[MPM]
	INT 224			;				[MPM]
	POP BX			;				[MPM]
MYCOM:	INC BX			; WRITE NEXT ONE		[MPM]
	JMPS WRTMX		;				[MPM]



CONINT: PUSHF			; disable Interrupts		[MPM]
	CLI
	CALL	SELECT		; select chip
;
	MOV	AL,4EH			;select 8 data bits, no parity, 1 stop
	OUT	MPORT,AL
;
	MOV	BL,Byte Ptr MSPEED	;Get Baud rate
	DEC	BL			;Adjust for Offset into table
	XOR	BH,BH
	MOV	AL,Byte Ptr BDTBL[BX]
	OUT	MPORT,AL
	MOV	AL,27H			;turn on DTR etc.
	OUT	CPORT,AL
	POPF				; restore Interrupts	[MPM]
	RET
;.....
;
;
; Use the 'SET' command to select a desired baud rate
;
SETUPR: MOV	DX,(Offset BAUDBUF)	;point to new input buffer
	CALL	JMP@ILPRT
	DB	'Input Baud Rate (300, 600, 1200, 2400, 4800, 9600, 19200): ',0
	CALL	JMP@INBUF
	MOV	DX,(Offset BAUDBUF)+2
	CALL	JMP@INLNCOMP		;compare BAUDBUF+2 with characters below
	DB	'300',0
	JNB	OK300			;go if got match
	CALL	JMP@INLNCOMP
	DB	'600',0
	JNB	OK600
	CALL	JMP@INLNCOMP
	DB	'1200',0
	JNB	OK1200
	CALL	JMP@INLNCOMP
	DB	'4800',0
	JNB	OK4800
	CALL	JMP@INLNCOMP
	DB	'2400',0
	JNB	OK2400
	CALL	JMP@INLNCOMP
	DB	'9600',0
	JNB	OK9600
	CALL	JMP@INLNCOMP
	DB	'19200',0
	JNB	OK19200
	CALL	JMP@ILPRT		;all matches failed, tell operator
	DB	'++ Incorrect entry ++',CR,LF,BELL,0
	JMP	SETUPR			;try again
;
OK300:	MOV	AL,1			;MSPEED 300 baud value
	JMPS	LOADBD			;go load everything
;
OK600:	MOV	AL,3
	JMPS	LOADBD
;
OK1200: MOV	AL,5
	JMPS	LOADBD
;
OK2400: MOV	AL,6
	JMPS	LOADBD
;
OK4800: MOV	AL,7
	JMPS	LOADBD
;
OK9600: MOV	AL,8
	JMPS	LOADBD
;
OK19200:MOV	AL,9
;
LOADBD: MOV	Byte Ptr MSPEED,AL	;change time-to-send to match baudrate
	JMP	CONINT			;reinitialize to new baudrate, then done
;...
;


;
SELECT:
	PUSH	AX
	PUSH	BX
	MOV	BL,COMCHA	; Translate Comm. Channel	[MPM]
	MOV	BH,0		; make 16 bit			[MPM]
	MOV	AL,CTRTBL[BX]	; Get corresponding port	[MPM]
	OUT	UPORT,AL	; Select USART
	POP	BX
	POP	AX
	RET
;
;
CTRTBL	DB	-1		; COMCHANNEL 0 DOES NOT EXIST	[MPM]
	DB	7
	DB	6
	DB	3
	DB	2
	DB	1
	DB	0
	DB	4
	DB	5
;....
;
;
; TABLE OF BAUDRATE PARAMETERS
;
BD300	EQU	35H			;300  baud
BD450	EQU	0			;450  baud NOT SUPPORTED
BD600	EQU	36H			;600  baud
BD710	EQU	0			;710  baud NOT SUPPORTED
BD1200	EQU	37H			;1200 baud
BD2400	EQU	3AH			;2400 baud
BD4800	EQU	3CH			;4800 baud
BD9600	EQU	3EH			;9600 baud
BD19200 EQU	3FH			;19200 baud
;
BAUDBUF DB	10,0
	RS	10

BDTBL	DB	BD300,BD450,BD600,BD710,BD1200,BD2400,BD4800,BD9600,BD19200
;
XIOS	DW 0		; keep XIOS offset here		[MPM]
	DW 0		; keep XIOS segment here	[MPM]

;
;
COMCHA	DB 0				; COMCHANNEL USED HERE		[MPM]
COMLST	DB 0,0,0,0,0,0,0,0,0		; MAX 8 CHANNELS + END MAKER	[MPM]

MXQPB	DW	0	;MXmodemN Que Parameter Block			[MPM]
	DW	0	;						[MPM]
	DW	1	;						[MPM]
	DW	OFFSET QUEBUF				;		[MPM]
qpbnam	DB	'MXmodem '

quebuf	dw	0

;
;	       (END OF INITMOD AND SETUP ROUTINES)
;=======================================================================
;
;
; If using the Hayes Smartmodem this is unavailable without a special
; change.
;
SPCLMENU:RET
;
;
; NOTE:	 MUST TERMINATE PRIOR TO 0400H (with Smartmodem)
;				 0C00H (without Smartmodem)
;.....
;
	END