; ; MXO-MR10.ASM - Morrow Micro Decision MD-11 overlay file for MEX ; or MDM712. ; 6/28/84 ; ; (Adapted from M712MD.ASM, originally for Morrow MD-2 & MD-3) ; ; You will want to look this file over carefully. There are a number of ; options that you can use to configure the program to suit your taste. ; This file adapts either modem program to the Morrow MD-11 computer. ; (It is not for use with the Morrow MD-2 or MD-3 computers.) ; While this computer has a number of serial ports, one is used for the ; terminal and the another for the printer/modem. To use this ; overlay, you must use the CP/M program "SETUP" to set the printer/ ; modem port to 1200 baud. (This is usually done automatically upon ; a boot.) Configure the internal jumpers to make the port a DTE ; type of device (page D-16 in my MD-11 User's Guide) for use with ; modems. ; ; Edit this file for your preferences then follow the "TO USE:" example ; shown below. ; ; Use the "SET" command to change the baudrate when desired. It starts ; out at 1200 baud when the program is first called up. If you exit ; the program while at 300 baud, re-boot the Morrow before proceeding ; in order to reprogram the Zilog DART to the correct clock ratio. ; (The SET command alters the DART clock divide ratio, not the ; clock frequency itself). Exiting the program when set to 1200 ; baud causes no such concern. (This advice only applies to usage ; of the SET command). ; ; TO USE: First edit this file filling in answers for your own ; equipment. Then assemble with ASM.COM or equivalent ; assembler. Then use DDT to overlay the the results ; of this program on the original MDM712.COM file (or ; follow the instructions with MEX to overlay MEX10.COM). ; ; For MDM712: ; ; A>SAVE ; A>DDT MDM712.COM ; DDT VERS 2.2 ; NEXT PC ; 4300 0100 ; -IMXO-MR10.HEX (note the "I" command) ; -R ("R" loads in the .HEX file) ; NEXT PC ; 4300 0000 ; -G0 (that's a zero: return to CP/M) ; ; CP/M 3 SAVE - Version 3.0 ; Enter file (type RETURN to exit): MODEM7.COM ; Beginning hex address 0100 ; Ending hex address 4300 ; A> ; ; You now have MODEM7.COM (or MEX.COM) for use on the ; Morrow MD-11. ; ; ; = = = = = = = = = = = = = = = = = = ; ; 06/28/84 - Further revisions & renamed for MEX- Steve Reyer ; 05/28/84 - Revised for use on Morrow MD-11 - Steve Reyer ; 07/21/83 - Renamed for use with MDM712 - Irv Hoff ; 07/01/83 - Revised for use with MDM711 - Irv Hoff ; 06/22/83 - Revised for use with MDM710 - Irv Hoff ; 06/22/83 - Altered MDM708DP for Morrow ; Micro Decision computers using ; an external modem - Irv Hoff ; ; = = = = = = = = = = = = = = = = = = ; BELL: EQU 07H ;bell CR: EQU 0DH ;carriage return ESC: EQU 1BH ;escape LF: EQU 0AH ;linefeed ; YES: EQU 0FFH NO: EQU 0 ; ; PORT: EQU 62H ;Morrow MD-11 prt/modem port MODCTL1: EQU PORT+1 ;Modem status port MODDATP: EQU PORT ;Modem data port MODCTL2: EQU PORT+1 ;Modem control port ; ; The following was added by Reyer to define the Zilog DART ; MODSNDB: EQU 04H ;bit to test for send MODSNDR EQU 04H ;value when ready MODRCVB EQU 01H ;bit to test for recv MODRCVR EQU 01H ;value when ready ; ; ORG 100H ; DS 3 ;(for "JMP START" instruction) ; PMMIMODEM: DB NO ;yes=PMMI S-100 Modem 103H SMARTMODEM: DB YES ;yes=HAYES Smartmodem, no=non-PMMI 104H TOUCHPULSE: DB 'T' ;T=Touch, P=Pulse (Smartmodem-only) 105H CLOCK: DB 40 ;clock speed in MHz x10, 25.5 MHz max. 106H ;20=2 MHh, 37=3.68 MHz, 40=4 MHz, etc. MSPEED: DB 5 ;0=110 1=300 2=450 3=600 4=710 5=1200 107H ;6=2400 7=4800 8=9600 9=19200 default BYTDLY: DB 5 ;0=0 delay 1=10ms 5=50 ms - 9=90 ms 108H ;default time to send character in ter- ;minal mode file transfer for slow BBS. CRDLY: DB 5 ;0=0 delay 1=100 ms 5=500 ms - 9=900 ms 109H ;default time for extra wait after CRLF ;in terminal mode file transfer NOOFCOL: DB 5 ;number of DIR columns shown 10AH SETUPTST: DB YES ;yes=user-added Setup routine 10BH SCRNTEST: DB YES ;Cursor control routine 10CH ACKNAK: DB YES ;yes=resend a record after any non-ACK 10DH ;no=resend a record after a valid NAK BAKUPBYTE: DB NO ;yes=change any file same name to .BAK 10EH CRCDFLT: DB YES ;yes=default to CRC checking 10FH TOGGLECRC: DB YES ;yes=allow toggling of CRC to Checksum 110H CONVBKSP: DB NO ;yes=convert backspace to rub 111H TOGGLEBK: DB YES ;yes=allow toggling of bksp to rub 112H ADDLF: DB NO ;no=no LF after CR to send file in 113H ;terminal mode (added by remote echo) TOGGLELF: DB YES ;yes=allow toggling of LF after CR 114H TRANLOGON: DB YES ;yes=allow transmission of logon 115H ;write logon sequence at location LOGON SAVCCP: DB YES ;yes=do not overwrite CCP 116H LOCONEXTCHR: DB NO ;yes=local command if EXTCHR precedes 117H ;no=external command if EXTCHR precedes TOGGLELOC: DB YES ;yes=allow toggling of LOCONEXTCHR 118H LSTTST: DB YES ;no=using modem on printer port 119H XOFFTST: DB YES ;yes=checks for XOFF from remote while 11AH ;sending a file in terminal mode XONWAIT: DB NO ;yes=wait for XON after CR while 11BH ;sending a file in terminal mode TOGXOFF: DB YES ;yes=allow toggling of XOFF checking 11CH IGNORCTL: DB YES ;yes=CTL-chars above ^M not displayed 11DH EXTRA1: DB 0 ;for future expansion 11EH EXTRA2: DB 0 ;for future expansion 11FH BRKCHR: DB '@'-40H ;^@ = Send 300 ms. break tone 120H NOCONNCT: DB 'N'-40H ;^N = Disconnect from phone line 121H LOGCHR: DB 'L'-40H ;^L = Send logon 122H LSTCHR: DB 'P'-40H ;^P = Toggle printer 123H UNSAVE: DB 'R'-40H ;^R = Close input text buffer 124H TRANCHR: DB 'T'-40H ;^T = Transmit file to remote 125H SAVECHR: DB 'Y'-40H ;^Y = Open input text buffer 126H EXTCHR: DB '^'-40H ;^^ = Send next character 127H ; ; DS 2 ; 128H ; IN$MODCTL1: IN MODCTL1 ! RET ;in modem control port 12AH DS 7 OUT$MODDATP: OUT MODDATP ! RET ;out modem data port 134H DS 7 IN$MODDATP: IN MODDATP ! RET ;in modem data port 13EH DS 7 ; ; ANI$MODRCVB: ANI MODRCVB ! RET ;Reyer: These lines were CPI$MODRCVR: CPI MODRCVR ! RET ;added to make it similar to ANI$MODSNDB: ANI MODSNDB ! RET ;similar overlays where the CPI$MODSNDR CPI MODSNDR ! RET ;UART flags needed testing DS 12 ; ; ; LOGONPTR: DW LOGON ;for user message. 160H DS 6 ; 162H JMP$GOODBYE: JMP GOODBYE ; 168H JMP$INITMOD: JMP INITMOD ;go to user written routine 16BH RET ! NOP ! NOP ;(by-passes PMMI routine) 16EH RET ! NOP ! NOP ;(by-passes PMMI routine) 171H RET ! NOP ! NOP ;(by-passes PMMI routine) 174H JMP$SETUPR: JMP SETUPR ; 177H JMP$SPCLMENU: JMP SPCLMENU ; 17AH JMP$SYSVER: JMP SYSVER ; 17DH JMP$BREAK: JMP SENDBRK ; 180H ; ; ; Do not change the following six lines. ; JMP$ILPRT: DS 3 ; 183H JMP$INBUF DS 3 ; 186H JMP$INLNCOMP: DS 3 ; 189H JMP$INMODEM DS 3 ; 18CH JMP$NXTSCRN: DS 3 ; 18FH JMP$TIMER: DS 3 ; 192H ; ; Clear sequences -- CLREOS is clear to end of screen, CLRSCRN is clear ; entire screen. Last entry must be 0. Any other 0's act as NOP's. ; The SCRNTST option must be set "YES" for these to work. These are now ; set for the Morrow MDT-60 terminal. ; CLREOS: CALL JMP$ILPRT ; 195H DB ESC,'Y',0,0,0 ; 198H RET ; 19DH ; CLRSCRN: CALL JMP$ILPRT ; 19EH DB ESC,'*',0,0,0 ; 1A1H RET ; 1A6H ; ; SYSVER: CALL JMP$ILPRT ; 1A7H DB 'Version for Morrow MD-11 hard-disk computer' DB CR,LF,0 RET ;..... ; ; ;----------------------------------------------------------------------- ; ; NOTE: You can change the SYSVER message to be longer or shorter. The ; end of your last routine should terminate by 0400H (601 bytes ; available after start of SYSVER) if using the Hayes Smartmodem ; or by address 0C00H (2659 bytes) otherwise. ; ;----------------------------------------------------------------------- ; ; You can put in a message at this location which can be called up with ; CTL-O if TRANLOGON has been set YES. You can put in several lines if ; desired. End with a 0. ; ; LOGON: DB 'This is a Morrow MD-11 computer',CR,LF,0 ;..... ; ; ;======================================================================= ; Extensive changes from the original Morrow overlay, M712MD.ASM ; have been made below by Reyer to accomodate the MD-11 and its ; Zilog DART (Dual UART). Notation such as "REG. 5" refers to ; write-registers in the Zilog DART. ; ; This routine allows a 300 ms. break tone to be sent to reset some ; time-share computers. ; SENDBRK: MVI A,05H ;SELECT REG. 5 OUT MODCTL1 MVI A,0FAH ;SEND BREAK ONLY OUT MODCTL1 JMP GOODBYE1 ;GO TO WAIT ;... ; ; ; This routine sends a 300 ms. break tone and sets DTR low for the same ; length of time to disconnect some modems such as the Bell 212A, etc. ; GOODBYE: MVI A,05H ;REG. 5 OUT MODCTL1 MVI A,7AH ;DTR OFF AND BREAK SENT OUT MODCTL1 GOODBYE1: MVI B,3 ;300 MS. CALL JMP$TIMER MVI A,05H ;REG. 5 OUT MODCTL1 MVI A,0EAH ;DTR ON, NO BREAK OUT MODCTL1 RET ; ; ; ;..... ; ; ; No initialization other than using SETUP (if needed) from ; CP/M is required. The following is part of the SET ; command code. (see OK300, OK1200, LOADBD, below). ; INITMOD: MVI A,5 ;TRANSFER TIME FOR 1200 BAUD STA MSPEED MVI A,04H ;SELECT REG. 4 OUT MODCTL1 INITMOD1: MVI A,44H ;DEFAULT TO /16 FOR 1200 BAUD OUT MODCTL1 IN PORT ;CLEAR DATA PORT RET ;..... ; ; SETUPR: LXI D,BAUDBUF ;POINT TO NEW INPUT BUFFER CALL JMP$ILPRT DB 'Input Baud Rate (300, 1200): ',0 CALL JMP$INBUF LXI D,BAUDBUF+2 CALL JMP$INLNCOMP ;COMPARE BAUDBUF+2 WITH CHARACTERS BELOW DB '300',0 JNC OK300 ;GO IF GOT MATCH CALL JMP$INLNCOMP DB '1200',0 JNC OK1200 CALL JMP$ILPRT ;ALL MATCHES FAILED, TELL OPERATOR DB '++ Incorrect entry ++',CR,LF,BELL,0 JMP SETUPR ;TRY AGAIN ; OK300: MVI A,1 ;MSPEED 300 BAUD VALUE MVI B,0C4H ;DIVIDE BY 64 FOR 300 BAUD JMP LOADBD ;GO LOAD THEM ; OK1200: MVI A,5 MVI B,44H ;DIVIDE BY 16 FOR 1200 BAUD ; ; LOADBD: STA INITMOD+1 ;CHANGE TIME-TO-SEND TO MATCH BAUDRATE MOV A,B ;GET BAUDRATE BYTE STA INITMOD1+1 ;STORE IN INITMOD JMP INITMOD ;REINITIALIZE TO NEW BAUDRATE, THEN DONE ; ; BAUDBUF: DB 10,0 DS 10 ;..... ; ; ; (END OF INITMOD AND SETUP ROUTINES) ;======================================================================= ; ; ; These routines can be used for your equipment, be sure to end with RET ; SPCLMENU: RET ; ;======================================================================= ; ; ; NOTE: MUST TERMINATE PRIOR TO 0400H (with Smartmodem) ; 0C00H (without Smartmodem). ; END ;